Forrest Saw Blades - NEW! LEECRAFT Zero-Clearance Inserts

#DL-1U Leecraft Zero-Clearance Table Saw Insert 13-3/8"L x 3-3/4"W

NEW! We are proud to offer LEECRAFT Zero-Clearance table saw inserts which are definitely SUPERIOR to any other brand! We think you'll agree that Leecraft's attention to detail and careful precision manufacturing are unmatched.

LEECRAFT Phenolic Table Saw Inserts reduce splintering and chip-out on the bottom side of regular or dado table saw cuts. The opening in the insert is cut on the table saw to the exact width of the saw blade’s kerf. The matching kerf prevents thin slices of wood from jamming in between the blade and the throat plate during a cut. It also reduces the amount of tear-out that can happen with a standard insert.

From the Manufacturer
The Zero Clearance concept is simple: the blade cuts its own perfectly sized slot by being raised through a machinable "blank" insert. Most inserts are 1/2-inch thick, high-density phenolic laminate, with a bonded-melamine surface. They offer superior rigidity, flatness, durability, and low friction and should not be confused with inferior HD/PP inserts. There's just no comparison! They feature leveling screws, side and end adjustment screws for a vibration-free fit, rear safety pin for lift-out protection, and a pre-cut blade bottom pocket that provides clearance for fully retracted blades and bevel cuts. Instructions also included. Use carbide-tipped blades only. A pre-cut starter pocket makes cutting the clearance slot easy and a finger hole makes for simple removal and hanging. Colors may vary. Made in USA.

Before ordering please measure your saw throat opening. Then check below to find the proper model for your table saw:

Model #CR-1 Leecraft Zero-Clearance Table Saw Insert fits Sears CRAFTSMAN 10" belt-drive models 1977 to mid 2004 (Check size, see DL-1U), RIDGID TS2412, TS2424, TS2400 (Please Note: CR-1 does not fit models TS2400LS, TS2400-1 or the new TS2410)

Model #CR-2 Leecraft Zero-Clearance Table Saw Insert fits Sears CRAFTSMAN, Older 10" belt-drive, Including models: 113.29901, 113.29903, 113.299040, 113.29943, 113.299142

Model #CR-3 Leecraft Zero Clearance Table Saw Insert fits Sears CRAFTSMAN, Vintage 10" belt-drive, including models: 103.29992, 113.27520, 113.27610, 113.27970, 113.29920, 113.29990, 113.29991, 113.29992

Model #DL-1U Leecraft Zero-Clearance Table Saw Insert fits DELTA: Unisaw & LEFT-TILT UNISAW, 10" Contractor, 10" Tilt Arbor Saw, "Hybrid" & Left-Tilt Contractor; GRIZZLY G1023; JET CTAS-10; POWERMATIC 63; CRAFTSMAN 22104, 22114, 22124; BRIDGEWOOD BW10TS; Steel City 35605, 35610, 35670, 35675, 35680, 35685

Model #DL-2 Leecraft Zero-Clearance Table Saw Insert fits DELTA 10" DIRECT DRIVE - Models include #34-670, #34-740 (Super-10), #36-380 (XL-10) #36-600, QT-10, TS-300 & TS-350 and JET #JSL-10TS SHOPLINE

Model #DW-2 Leecraft Zero-Clearance Table Saw Insert fits DeWALT: DW744 & DW745 (factory splitter/guard incompatible with DW-2 insert on these saws) & DW746

Model #GE-1 Leecraft Zero-Clearance Table Saw Insert fits GENERAL International: 350 (Right Tilt) & 650 (Left Tilt)

Model #GE-2 Leecraft Zero-Clearance Table Saw Insert fits GENERAL International: 50-220, 50-090K; JET: 10" Workshop Table Saw (Stock #708100), JPS-10 Pro-Shop, JPS-10TS (Stock #708482, 708483, 708480K) and the Woodtek 10" Hybrid Table Saw

Model #GE-3 Leecraft Zero-Clearance Table Saw Insert fits GENERAL International: 50-075/175/185/250/260

Model #HT-1 Leecraft Zero-Clearance Table Saw Insert fits HITACHI: C10FL & C10LA

Model #JT-164 Leecraft Zero-Clearance Table Saw Insert fits JET: JTS-10, JCS-10, JWTS-10, JTAS-10, JWCS-10; POWERMATIC: 64 & 64A (left-tilt); SUNHILL: most 10" saws; BRIDGEWOOD: TSC-10C & TSC-10CL; KING KC 10GC; SHOP FOX: W1703, W1714, W1725, W1726; GRIZZLY: G0444, G0444Z, G0575, G0576

Model #JT-2L Leecraft Zero-Clearance Table Saw Insert fits JET XACTA SAW LEFT (JTAS-10XL); SHOP FOX: W1677, W1711; GRIZZLY G1023SL

Model #JT-5 Leecraft Zero-Clearance Table Saw Insert fits JET Deluxe XACTA Saw - Zero Clearance (with riving knife slot)

Model #JT-6 Leecraft Zero-Clearance Table Saw Insert fits JET Deluxe XACTA Saw - Zero Clearance/Dado (WITHOUT riving knife slot)

Model #JT-SS Leecraft Zero-Clearance Table Saw Insert fits Jet Super Saw

Model #PM-1 Leecraft Zero-Clearance Table Saw Insert fits POWERMATIC 66; BRIDGEWOOD BW10LTS

Model #PM-6 Leecraft Zero-Clearance Table Saw Insert fits POWERMATIC PM2000 - Zero Clearance (riving knife slot)

Model #PM-7 Leecraft Zero-Clearance Table Saw Insert fits POWERMATIC PM2000 - Zero Clearance/Dado (without riving knife slot)

Model #RG-1 Leecraft Zero-Clearance Table Saw Insert fits ONLY RIDGID TS3650, TS3660

Model #RG-2 Leecraft Zero-Clearance Table Saw Insert fits RIDGID TS2400-1, TS2400LS, and TS2410LS saws

Model #RG-3 Leecraft Zero-Clearance Table Saw Insert fits the new RIDGID R4510

Model #SC-1 Leecraft Zero-Clearance Table Saw Insert fits Steel City 10" Cabinet Saw Model #35900 Series - Zero Clearance (riving knife slot) Rigid R4511

Model #SC-2 Leecraft Zero-Clearance Table Saw Insert fits Steel City 10" Riving Knife Cabinet Saw Model #35900 Series - Zero Clearance/Dado (WITHOUT riving knife slot) Rigid R4511

	#DL-1U Leecraft Zero-Clearance Table Saw Insert 13-3/8"L x 3-3/4"W Model: DL-1U Diameter: Bore: Price: $22.99 Kerf: Plate: Teeth: Tooth Style:
#DL-1U Leecraft Zero-Clearance Table Saw Insert fits DELTA: Unisaw & LEFT-TILT UNISAW, 10" Contractor, 10" Tilt Arbor Saw, "Hybrid" & Left-Tilt Contractor; GRIZZLY G1023; JET CTAS-10; POWERMATIC 63; CRAFTSMAN 22104, 22114, 22124; BRIDGEWOOD BW10TS; Steel City 35605, 35610, 35670, 35675, 35680, 35685 INSTALLING AND FITTING YOUR INSERT (Note: This insert does not require the front hold-down screw utilized on your original factory insert.). Lower the blade completely. Place insert in table with lug at rear and starter pocket located over blade. Run leveling screws down until insert is stable and flush with table top. Back out front end-adjustment screw and side adjustment screw to achieve a fit that is snug, yet removable. If the insert will not go down flush with table top because it is resting on top of blade, then raise up using leveling screws until insert is sitting steady slightly above table top. This should provide adequate clearance for blade. SPLITTER: If your saw has a splitter, you will need to cut a slot at the rear of the insert to accommodate it. Trace the outline of the slot from your original metal insert, and cut with bandsaw or hacksaw. Leave the bridge between the splitter slot and the blade slot as thick as possible. CUTTING THE BLADE SLOT (KERF) Check that insert is fitted properly, and that blade is clear. Using a stick, reach under the table and rotate the blade manually to check for blade clearance. Fully cover the insert with a board, and clamp at each end to the table saw top. Re-connect power to saw. Switch on, slowly and cautiously raise blade up, to cut its way through the insert. KEEP HANDS OFF OF TABLE TOP, STAY CLEAR AND WEAR GOGGLES. Raise blade to maximum height at this time. Lower blade, turn off saw, and remove board. Your insert is now ready for use! IMPORTANT TIPS FOR USE Only recommended for use with carbide tipped cutters. DADO BLADE - Use same procedures outlined above, but use additional caution due to excessive material being machined from insert during the slotting procedure. Under certain conditions, an undesirable scraping noise may be generated by your saw blade. Planer type blades and/or excessive arbor run-out, and/or blade distortion, may be causing intermittent contact with the insert slot. To remedy this, remove the insert and slightly widen the slot using a file or sanding paddle. Ideally, a separate insert should be used with each blade, dado stack, or angle set-up. This will insure a true "zero-clearance" effect and give you maximum benefit from your inserts.

Need help picking the correct Forrest Saw Blade or accessory?

See our Application Chart, or Contact Us for expert advice