NEW! We are proud to offer LEECRAFT Zero-Clearance table saw inserts which are definitely SUPERIOR to any other brand! We think you'll agree that Leecraft's attention to detail and careful precision manufacturing are unmatched.
LEECRAFT Phenolic Table Saw Inserts reduce splintering and chip-out on the bottom side of regular or dado table saw cuts. The opening in the insert is cut on the table saw to the exact width of the saw blade’s kerf. The matching kerf prevents thin slices of wood from jamming in between the blade and the throat plate during a cut. It also reduces the amount of tear-out that can happen with a standard insert.
From the Manufacturer
The Zero Clearance concept is simple: the blade cuts its own perfectly sized slot by being raised through a machinable "blank" insert. Most inserts are 1/2-inch thick, high-density phenolic laminate, with a bonded-melamine surface. They offer superior rigidity, flatness, durability, and low friction and should not be confused with inferior HD/PP inserts. There's just no comparison! They feature leveling screws, side and end adjustment screws for a vibration-free fit, rear safety pin for lift-out protection, and a pre-cut blade bottom pocket that provides clearance for fully retracted blades and bevel cuts. (Some inserts use OEM screws to hold inserts in place). Instructions also included. Use carbide-tipped blades only. A pre-cut starter pocket makes cutting the clearance slot easy and a finger hole makes for simple removal and hanging. Colors may vary. Made in USA.
BEFORE ORDERING: MEASURE YOUR SAW THROAT OPENING TO PREVENT DELAYS. THEN CHECK BELOW TO FIND THE PROPER MODEL FOR YOUR TABLE SAW.
Model #BH-1 13-9/16"L x 3-3/4"W x 7/16" Thick - WITH RIVING KNIFE SLOT. Fits Bosch 4000 and 4100 models.
Model #BH-2 13-9/16"L x 3-3/4"W x 7/16" Thick - WITHOUT RIVING KNIFE SLOT for dado sets. Fits Bosch 4000 and 4100 models
Model #CR-1 14"L x 3-3/4"W x 3/16" Thick - Fits Sears CRAFTSMAN 10" belt-drive models 1977 to mid 2004 (Check size, see DL-1U), RIDGID TS2412, TS2424, TS2400, TS3612 (Please Note: CR-1 does not fit models TS2400LS, TS2400-1 or the new TS2410)
Model #CR-2 14-3/8"L x 3-3/4"W x 3/16" Thick - Fits Sears CRAFTSMAN, Older 10" belt-drive, Including models: 113.29901, 113.29903, 113.299040, 113.29943, 113.299142
Model #CR-3 14-3/8"L x 3-3/4"W x 3/32" Thick - Fits Sears CRAFTSMAN, Vintage 10" belt-drive, including models: 103.29992, 113.27520, 113.27610, 113.27970, 113.29920, 113.29990, 113.29991, 113.29992
Model #CR-4 15-1/8"L x 4-1/8"W x 1/8"T - Fits Sears CRAFTSMAN #351.218330
Model #DL-1U 13-3/8"L x 3-3/4"W - Fits DELTA: Unisaw & LEFT-TILT UNISAW, 10" Contractor, 10" Tilt Arbor Saw, "Hybrid" & Left-Tilt Contractor, Delta X5; GRIZZLY G1023; JET CTAS-10; POWERMATIC 63; CRAFTSMAN 22104, 22114, 22124; BRIDGEWOOD BW10TS; Steel City 35605, 35610, 35670, 35675, 35680, 35685
Model #DL-2 12-1/2"L x 3-3/4"W - Fits DELTA 10" DIRECT DRIVE - Models include #34-670, #34-740 (Super-10), #36-380 (XL-10) #36-600, QT-10, TS-300 & TS-350, JET #JSL-10TS SHOPLINE and JTS-10DD
Model #DL-614-1/2"L x 5"W - Fits NEW DELTA UNISAW Model #36-L336,36-L352, & 36-L552 (without riving knife slot).
Model #DL-714-1/2"L x 5"W (WITH riving knife slot) fits NEW DELTA UNISAW Model #36-L336,36-L352, & 36-L552.
Model #DW-2 13-9/16"L x 3-3/4"W - Fits DeWALT: DW744 & DW745 (factory splitter/guard incompatible with DW-2 insert on these saws) & DW746
Model #GE-1 13-13/16" x 3-1/2" - Fits GENERAL International: 350 (Right Tilt) & 650 (Left Tilt)
Model #GE-2 14-31/32"L x 3-23/32"W - Fits GENERAL International: 50-220, 50-090K; JET: 10" Workshop Table Saw Newer Model-#JWTS-10 - older version (Stock #708100) (Please check size before ordering), JPS-10 Pro-Shop, JPS-10TS (Stock #708481, 708482, 708483, 708480K) and the Woodtek 10" Hybrid Table Saw
Model #GE-3 12-9/16"L x 3-9/16"W - Fits GENERAL International: 50-075/175/185/250/260
Model #HT-1 15-1/8"L x 3-3/4"W x 1/8"T - Fits HITACHI: C10FL & C10LA and Porter Cable PCB270TS